Instruction
How to Obtain Slicing Files (.zslr) and Project Files (.zprj)
This article applies to UNIZ Dental V1.0, UNIZ Dental V2.0, and UNIZ Industry software. What are Slicing Files and Project Files? Slicing Files (.zslr): Definition: Slicing files are direct instruction sets used by the printer to convert 3D models ...
How to replace the mainboard
This article applies to NBEE, NBEE J, NBEE D, and NBEE H printer. Before replacement Items to prepare: ①New mainboard;②Hexagon Wrench M3. Report SN to UNIZ support: How to get SN. Please ignore if it has been sent to UNIZ support team ...
How to replace the screen cable
This article applies to NBEE , NBEE D , NBEE H. Description The LCD screen cable refers to the cable that connects the liquid crystal display screen (LCD screen) to the main control board (HDMI board). This cable usually is responsible for ...
How to get SN for NBEE?
What is SN? SN refers to the printer's serial number (Serial Number). This serial number is a unique identifier assigned to each printer by UNIZ factory. What is SN used for? The serial number can be used to verify the device's warranty status and ...
How to deal with the resin on the LCD screen
Possible Causes Accidentally dripping resin onto the LCD screen when moving the build platform or resin tank. The damage of the resin tank led to the resin seep onto the LCD screen during the printing process. In daily use, please keep the LCD screen ...
How to replace HDMI board for NBEE?
Preparation Socket Wrench; A new HDMI board. Step1: Remove the faulty HDMI board Power off the printer; Remove the front casing and put it aside, be careful of the connected cables; Unscrew the 3 nuts on the HDMI board； Remove the HDMI board from the ...
How to replenish coolant in NBEE
Preparation before operation Prepare items: ①M4 hexagonal wrench ②UNIZ brand coolant ③Nitrile gloves Operation steps Turn off the printer and unplug the power cord; Remove the rear casing of the printer; There are wires connected to the rear casing. ...
How to drain coolant from NBEE
When does coolant need to be drained When the coolant becomes murky and no longer transparent, it is necessary to drain the old coolant, clean the cooling system and fill in new coolant； When the cooling board is cracked or crushed, necessitating ...
How to check firmware (SYS version) and UI version
1. Go to System>System and Updates 2. View current system version Note: Make sure the system version and UI version match UI & SYS Match Checklist UI Link SYS Link 3.8 Download 4.6 OTA 3.7 NA 4.5 OTA 3.6 NA 4.4 OTA 3.5 NA 4.3 OTA 3.4 NA 4.2 OTA To ...
How to upgrade firmware
Why Upgrade? UNIZ R&D team continues to optimize product functions and features, and will upgrade and optimize the printer host computer (software) and printer (Firmware_SYS). In order to experience better product features, you can optionally ...
NBEE Fresnel Lens Replacement Guide
Preparation Allen wrench Phillips screwdriver New fresnel lens Steps Unscrew these 6 screws to separate the rear casing from the printer. Push the rear casing back slightly and disconnect the observation light cable.Then remove the front and back ...
How to replace NBEE Limit Switch
Preparation Required materials: a) Hexagon Wrench M3 b) Limit switch; Begin the procedure with the printer powered off; Remove and install Remove the three screws on the back of the printer to open the round rear cover; Remove the two screws holding ...
How to import third party resin into UNIZ Dental V2
Steps Log in to UNIZ official website and go to the lowest navigation bar of the page enter Open Material Library.Or enter the URL：https://www.uniz.com/us_en/materials/open-material-library Find the resin brand you need to download, click the plus ...
How to upgrade UI
Part 1: Preparations Please make sure the firmware SYS has been upgraded to the corresponding version. For details, please refer to below chart "UI & SYS Matching List" UI & SYS Match Checklist UI Link SYS Link 3.8 Download 4.6 OTA 3.7 NA 4.5 OTA 3.6 ...
How To Change Resin Tank Film
The resin tank film is transparent. Before installing the film, please remember to remove the protective films from both sides of the resin tank film. Steps Make sure the Resin Tank is wiped clean inside and out, and put it on a clean table. Flip the ...